독립적인 벤치 특성화 및 공개된 벤치 노트는 63V 등급의 박막 1206 SMD 퓨즈가 정상 상태 정격보다 훨씬 높은 짧은 펄스를 방해할 수 있음을 보여줍니다. 이 포괄적인 가이드는 전기 및 기계 사양, 실험실 테스트 방법 및 PCB 통합에 대해 자세히 설명합니다.0437001. WRA소형 전력 설계에서.
Note for Designers:All numeric recommendations below are presented as either measured bench results or recommended datasheet-constrained values. Validate final choices on full production samples prior to qualification.
Product Background & Key Specifications
The0437001.WRA최대 63V의 저전압 파워 레일을 위해 설계된 1206 형식의 박막, 고속 작동 SMD 퓨즈입니다. 설계자의 핵심 필드에는 공칭 전류(1A 일반), 전압 한계(63V DC/AC) 및 열 제약 조건이 포함됩니다.
주요 전기 및 기계 사양
| 필드 | 일반적인 값/주석 |
|---|---|
| Nominal current rating | 1 A (Datasheet) |
| Voltage rating | 63V DC / 63V AC (Datasheet) |
| Interrupt rating | 정격 전압에서 최대 50A 피크(측정된 샘플) |
| 불 특성 | 빠른 연기, 얇은 필름 |
| 케이스 사이즈 | 1206(3216 메트릭) |
| Typical cold resistance | ~0.15–0.5 Ω (Measure per sample) |
| Operating ambient | -55°C to +125°C |
Package, Marking & Footprint Considerations
권장 PCB 랜드 패턴은 솔더 필릿 및 열 소산을 최적화하기 위해 1206 칩의 공식 패드 형상을 따릅니다. 리플로우 프로필 제약 조건은 표준 무연 프로토콜을 따라야 합니다. 패키지 전쟁을 방지하기 위해 피크 보드 온도 노출을 제한합니다. 기계적 응력이 집중되는 퓨즈 아래의 라우팅을 피하십시오.
전기 성능 및 데이터 분석
시간-전류 및 정보 기술 동작
시간-전류 곡선은 고정 영역과 용융 영역 간의 급격한 전환을 나타냅니다. 빠르게 작동하는 분류의 경우 용융 I²t(개방 에너지)가 낮으므로 유입 허용 오차가 제한됩니다.
Visual Data RepresentationVoltage & Derating Guidance
전압 제한은 최대 63V입니다. 감압 지침: 연속 전류 용량을 70°C 주변보다 약 10-20% 줄입니다. DC 시스템에서는 꾸준한 열 축적으로 인해 더 촘촘한 여백을 적용합니다.
테스트, 방법론 및 합격/불합격 제한
표준화된 실험실 테스트
- •Apply incremental current steps (1.25×, 1.5×, 2×).
- •Perform short-circuit interruption at rated voltage.
- •Log surge/inrush waveforms using high-bandwidth probes.
수락 기준
- •정격 전류를 ≥분 동안 100% 유지해야 합니다.
- •지속적인 불꽃이나 빛이 없는 중단.
- •Post-test resistance must remain within change %.
Typical Applications & Case Examples
Fast 1206 SMD fuses with a 63V rating suit compact 12–48V power rails, battery-protected logic lines, and step-down converter inputs. The 63V headroom is ideal for vehicle or portable systems where transients occur.
흐름:돌입 I²t를 계산하세요. 만약 돌입 I²t가 있을 때
Selection, PCB Integration & Maintenance Checklist
How to Choose
- Verify interrupt rating ≥ possible short-circuit current.
- Ensure voltage rating ≥ system maximum + margin.
- Check reflow profile tolerance and environmental ratings.
설치 모범 사례
- 인접한 추적에 열 릴리프를 제공합니다.
- 시각적 솔더 필릿 검사 및 연속성 테스트를 수행합니다.
- 필드 정책 유지: 서비스 로그에 모든 퓨즈 교체를 기록합니다.
Summary
Verification
Verify nominal current, 63V rating, and I²t values. Document datasheet vs. measured results for every lot.
Testing
Characterize time-current, interrupt performance at rated voltage, and production-profile survivability.
통합
정확한 패드 형상을 따르고 기계적 간격을 유지하여 응력 및 재작업 위험을 줄입니다.
